Formation of porous polymer morphology by microsyneresis during divinylbenzene polymerization

This article describes the investigation of the importance of various reaction conditions on microsyneretic pore formation during polymerization of divinylbenzene (DVB) under so‐called “solvothermal” conditions. To induce microsyneretic pore formation, the most important parameter is an unusually high dilution of monomers with a “good” porogen solvating the polymer chains. High dilution and solvation of the growing poly(DVB) chains promote the prolongation of the polymer chains rather than their interconnection by crosslinking. Consequently, when the polymer gel density reaches the point where syneresis starts, the polymer network is geometrically too extensive to be broken up into precipitating entities and, instead, porogen droplets are formed within the continuous polymer gel. The pore geometry created by microsyneresis offers high surface area in wide mesopores and hence, high capacity for supporting functional groups or reactions with much better accessibility than narrow pores between polymer microspheres produced by macrosyneresis in conventional styrenic polymer supports. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 774–781     

Enhancing the Water Stability of Al‐MIL‐101‐NH2 via Postsynthetic Modification

The resistance of metal–organic frameworks towards water is a very critical issue concerning their practical use. Recently, it was shown for microporous MOFs that the water stability could be increased by introducing hydrophobic pendant groups. Here, we demonstrate a remarkable stabilisation of the mesoporous MOF Al‐MIL‐101‐NH₂ by postsynthetic modification with phenyl isocyanate. In this process 86 % of the amino groups were converted into phenylurea units. As a consequence, the long‐term stability of Al‐MIL‐101‐URPh in liquid water could be extended beyond a week. In water saturated atmospheres Al‐MIL‐101‐URPh decomposed at least 12‐times slower than the unfunctionalised analogue. To study the underlying processes both materials were characterised by Ar, N₂ and H₂O sorption measurements, powder X‐ray diffraction, thermogravimetric and chemical analysis as well as solid‐state NMR and IR spectroscopy. Postsynthetic modification decreased the BET equivalent surface area from 3363 to 1555 m² g^?1 for Al‐MIL‐101‐URPh and reduced the mean diameters of the mesopores by 0.6 nm without degrading the structure significantly and reducing thermal stability. In spite of similar water uptake capacities, the relative humidity‐dependent uptake of Al‐MIL‐101‐URPh is slowed and occurs at higher relative humidity values. In combination with ¹H‐²⁷Al D ‐HMQC NMR spectroscopy experiments this favours a shielding mechanism of the Al clusters by the pendant phenyl groups and rules out pore blocking.     

Micro enzymatic assay coupled to capillary electrophoresis via liquid junction

Summary A system for capillary electrophoresis combined with enzymatic assay has been evaluated for the two enzymes glucose-6-phosphate dehydrogenase and 6-phosphogluconate dehydrogenase. Instrumentation included a post-column reactor coupled to the separation capillary by a liquid junction. A technique for generating a substrate solution flow into the reactor by utilizing two high voltage supplies is proposed. This method offers a high degree of freedom in optimizing the separation and enzymatic reaction conditions individually. Possibilities for improving the enzymatic assay sensitivity were also examined.     

Extrusion of pastes with a piston extruder for the determination of the local solid and fluid concentration, the local porosity and saturation and displacement profiles by means of NMR imaging

 Nuclear Magnetic Resonance (NMR) was used to investigate the extrusion behaviour of PTFE pastes in a ram extruder. By means of ¹H-NMR imaging (MRI) it is possible to determine the local proton density and therefore, the local fluid concentration. The ¹⁹F-MRI provides the local solid concentration. Thus the local saturation and the local porosity can be calculated with the information of the local fluid and solid concentration. Furthermore displacement profiles can be derived from NMR images by means of correlation techniques without any preparation or marking of the pastes. Received: 8 May 2000   Accepted: 1 May 2001     

微全分析系统检测方法的研究进展

综述了不同类型的检测方法在微全分析系统的应用，并简述了各类型的检测方法的优缺点。引用文献92篇。     

三维流动传热空隙率计算程序FASTOR—3D开发研究

1引言大粘度（大r）和大系数（ss和sc）法是处理流动区域中障碍物的常用方法山。但当流动区域中障碍物数量较多时，宜采用空隙率来模拟障碍物，如模拟反应堆流动传热的商用程序COMMIX［’］。我们根据空隙率模拟的基本概念，针对采用交错网格的压力校正法，自行编制了多障碍物流动传热三维计算的全部源程序代码，应用于某核反应堆钠池流动传热的数值模拟，获得了比较合理的结果。2数学模型和数值方法2．1控制方程空隙率修整的质量、动量、能量及湍流动能与耗散率的守恒方程通式的三维柱坐标形式为其中中一1，。，。，。，T，k，。分别表…     

Quality assurance for the analytical data of micro elements in food

The micro element content of food is an important quality index due to the action of these elements on human health. In this article, we discuss how to ensure the reliability of analytical data on micro elements in order to truly represent the condition of food. Sampling, treatment of the analytical sample, selection of the analytical method, standard solution, and certified reference material, blank test, calibration of the instrument and equipment, application of the quality control chart, assessment of the final analytical result, and quality assurance system are briefly described. Received: 5 July 2001 Accepted: 19 November 2001     

Consolidation around a borehole embedded in media with double porosity under release of geostatic stresses

The paper deals with the stress, displacement, pore and fissure pressures fields induced by the drilling and/or the pressurization of a vertical borehole in a formation of water-saturated porous media with double porosity. The solution includes the boundary condition of non-hydrostatic in situ state of stress. The solid skeleton is assumed to behave as a linearly poroelastic material with compressible constituents. The analytical solution is derived in Laplace’s space and transformed to the time domain using a numerical inversion technique. The histories of pore and fissure pressures are illustrated to show the influence of permeabilities of the pore and fissure systems.     

POROSITY CALCULATION OFMIXTURES OF FIBROUS PARTICLES

The initial forming of fiber blend to high green density, i.e. the packing of fibrous particles, is important to the reinforcement of composite materials. It is very useful to develop a general predictive method for the optimum selection of particle mixtures for the property control of ceramic or composite products. This paper presents such a mathematical model developed on the basis of the similarity analysis between the spherical and non-spherical particle packings and assesses its applicability to the packing of fibrous particles with discrete and/or continuous length distributions. The results indicate that the model can predict this packing system well and hence provide an effective way to solve various packing problems in the composite materials processing.